Checked unit over found that the dishwasher would intermittently power on and shut off and you could not get it to stay on for a long period of time. Unit needs new control board and user interface. Dishwasher is also leaking and flooding the customers wood floors. Found that the unit was leaking from where the tub was welded together on the back right corner. Unit needs a new tub and lower spray arm. Spoke with AHS and they're putting into options.

Inspected unit and found a failed convection fan motor. Tested the front right burner and infinite switch and it passed according to manufacturer standards for temperatures on a fast broil element. Provided information to customer about how this fast broil burner works, it does not do well low temperatures. Estimate provided and approved. installed parts and ran a test cycle. All checks ok.

Icemaker is functioning properly. A large amount of ice was just build up in the bin and not allowing it to dispense. Cleared ice and let the customer know they will need to empty it out periodically to prevent that from happening. All checks OK

Repaired door switch checks ok

Found the element and filter defective. Installed parts. All checks ok. ; used 1 De486a (Heater) from stock

Replaced parts, all checks okay

"Inspected the unit and found the hot water valve squealing. Ran a test cycle and the unit filled with hot and cold water, agitated, drained and spun without any other issues. No error codes located. Gave information to the customer about the cold water valve leaking from time to time. Provided estimate and the customer approved replacing both valves. Installed valves and ran test cycle. All checks OK"

Ice maker is locked up. Replaced the ice maker; used 1 241798224 (Imk) from stock

Installed parts. All checks ok. Advised the customer it can take 24 hours or more before the unit gets back to normal temperatures.

Installed board. All checks OK

Installed new condensor fan, it was locked up

Unit needs new control board, evaporator fan, and motor not communicating to cool unit. Gave estimate!

Installed new tstat , checks okay

Damper was stuck, gave an estimate to replace the damper

Installed new defrost heater and control board.

Installed parts listed. All checked ok

Installed parts listed. Checks okay

Found UI harness loose. Reseated and all checked ok. Reset control and operating as it should.

Replaced parts, all checks okay

Dryer operating fine. Vibration is typical. Advised customer that unit will have some vibration. All checked ok

"Found fill tube frozen, not allowing icemaker to fill properly, removed ice build up, unit checks ok."

Installed parts listed checks ok

"Installed new valve assembly, unit checks ok."

"Installed float switch, unit checks ok."

"Installed new control board, unit checks ok."

"Installed gaskets, unit checks ok."

"Found drain pump not turning with proper voltage applied, installed new drain pump, drain tube packed full of food, not allowing unit to drain properly. Customer to replace drain tube."

"Found water valve not opening properly, installed new valve assembly, unit checks ok.; used 1 242253002 (WATER VALVE) from stock"

"Found lid lock will not engage, installed new lid lock, unit checks ok."

"Found unit leaking from water valve assembly, giving LE error code, intermittent drain issue, customer decided to replace unit."

Installed new parts and checked the water pressure coming out of the hoses. The cold water hose water pressure was significantly less than the hot water. Informed customer and showed him. He said he would look into this further. I explained that it will probably keep doing the same thing if the water pressure in the cold water hose isnt higher.

Inspected unit and found the water not coming into the unit from the water valve. Checked the hoses to the water valve and had proper water flow to the unit. Replaced water valve and ran tests. All checks ok. ; used 1 5221EA1008F (Water valve) from stock

Inspected unit and Found fan working properly. I took the fan cover off and tightened the fan all the way. Customer was concerned because it was loud. I explained to them that some manufacturers are louder than others. All checks ok.

Upon arrival I started a quick wash cycle to test the washer to make sure it was running through its cycles properly. Unit is cycling like its supposed to. Not finding anything wrong with the unit. Showed customer when it started its rinse cycle that it did go through a rinse and working properly. All checks ok.

Inspected the unit and found the icemaker mold not filled with water. Customer stated that the back right of the unit leaks occasionally. Remove the back panel and found water marks coming from the water valve and drain pan. Filled the drain pan up with water and found no leaks. Ran 40 ounces of water through the filter and the waterline did not leak. Customer said the leak is sporadic. Ordering water valves and control board.; rqstng P&A on 1 5304526176 (Board) and 1 5304519114 (Pc board) and 1 5304519215 (Inlet valve) and 1 5304519149 (Dual water valve)

Checked unit over found that the unit was not heating the water and the unit had multiple lights out on the display. Unit needs a new control and display due to being shorted out. Unit is not cleaning and is leaking water. Unit needs a new wash motor and sump assembly. Unit is about 15 years old in the kitchen; rqstng P&A on 1 W10482480 (Sump assembly) and 1 W10551673 (Touchpad) and 1 W10510666 (Motor) and 1 W10804120 (Control)

Checked unit over and found the unit was leaking from the bottom tub seal and also leaking oil from the gear case. Unit needs outer tub and gear case. Unit is about 10 years old. In the laundry room; rqstng P&A on 1 #### (Gearcase) and 1 #### (Outer tub)

Replaced parts, all checks okay

Inspected the unit and the control board kept making weird noises and sounds but will not power up or run through a cycle. Ordering control board and panel. unit is five years old and located in the laundry room; rqstng P&A on 1 DC92-01623G (Control) and 1 DC97-19576U (UI panel)

Unit is turning off & on will need main board replaced; ordrng 1 W10310240 (Cont brd)

Cleaned out the drain line and had customer defrost it for 24 hours and the issue was still returned. Will contact Frigidaire extended warranty tomorrow and ask about what the next steps are in repairing unit or replacing it.; saved tckt

Inspected the unit and found no voltage coming from the control to Icemaker. Ordering control.; ordrng 1 W10226427 (Control)

Knob selection isnt working all the time. Needs control knob board. ; rqstng P&A on 1 EBR85194701 (UI board.)

Unit not heating ; rqstng P&A on 1 5304509460 (Switch) and 1 5304520021 (Switch) and 1 5304509470 (Magnetron) and 1 5304509478 (Capacitor) and 1 5304515185 (Diode) and 1 5304513462 (Thermostat) and 1 5304513463 (Thermostat)

Rebooted the unit and came back needs new main board; ordrng 1 W10843055 (Brd) and 1 W10830278 (Brd) and 1 W10830288 (Cont brd)

"Ordering door hinge. ; rqstng P&A on 2 WE01X31005 (Door hinge)s"

Inspected unit and found the drain pump humming but not draining any of the water out. Called techline to get part number for drain pump. Ordering drain pump. ; rqstng P&A on 1 11001011000071 (Drain pump)

"When installing new motor, I could not break the blower fan free from the motor. Ordering blower housing assembly. ; ordrng 1 134690800 (Blower housing) and 1 134707900 (Motor lock)"

"Inspected unit and found microwave running but not heating up. Plate was turning and fans were on. Ordering magnetron, diode, capacitor and control board. ; rqstng P&A on 1 Eas61382906 (Magnetron) and 1 Acm74818821 (Control board) and 1 6501w1a006a (Diode)"

Checked unit over found that the unit was cooling properly and did not have any frost buildup in the freezer. Refrigerator was at correct temperatures. Checks OK

Checked unit over found that the unit was heating and everything was functioning properly. Multiple buttons on the touchpad are worn off. Called American home shield and gave them this information. Due to the unit functioning normal and the issues are solely being cosmetic American shield is not going to cover replacing the control panel.

Replace water valve to icemaker due to the unit not filling with water. Tested unit checks OK

"Unit still need new main control, board isnt available. No repair"

Replaced parts, checks okay

Checked unit over from bad connection on waterline. Repaired water line at valve. Checks OK

Replaced burner switch provided by customer. Checks ok

Replaced suspension rods. Checks ok

Replaced parts listed checks.

No issues, noises coming from expansion as it heats.

Disassembled and replaced cooling fan. Checks ok

Repaired broken wire on compressor. Checked OK

Disconnected shorted timer that was constantly buzzing. Spoke with HBW and they wont cover timer repair due to unit functioning normal and timer not affecting functionality.

Inspected unit and found an issue with the belt. All checks OK

Inspected the unit and found a plastic guard for the drum had come loose and was rubbing on the unit. Also found a large amount of lint buildup inside the unit found the motor. Cleared out and repaired guard. All check ok. Provided estimate to Aarons and they approved.

"Inspected the unit and when attempting to spin the basket I could hear loud grinding noise in the basket wobbling it will not spin freely. Removed the washplate bolt and washplate, inspected the inner and outer baskets, found no clothing or debris preventing the basket from spinning. Found a small amount of grease around the gearcase head. Pulled the unit away from the wall and inspected the underside. Found the rotor and stator in place and the bolt tightly secured. Found a small amount of grease leaking from the gearcase. Attempted to pull the inner basket up and off the gearcase and it would not move. The gearcase has cracked and become stuck to the outer and inner baskets. The repair will require to replace the outer and inner tubs along with the gearcase and fittings. The repair is very expensive and the tech does not recommend the repair due to cost and potential future issues with repair. The unit is only a few years old per the customer."

"Inspected the unit and found issues with the door lock. It is now functioning properly, tested multiple times. All checks OK"

Inspected the unit and found the door latch not lined up with the strike. Disassembled the door and made adjustments to the door latch and strike. The doors not opening closing properly without any issues.

Installed updated ice room housing checks ok

Customer wanted the drain filter removed and cleaned out and could not remove the filter. Removed the filter and cleared debris. Made adjustments to the drain pump and filter. Demonstrated to The customer how to remove it and install it correctly. All checks OK

"Inspected the unit and found the griddle element intact and the wiring in good condition. Found the thermostat connected properly and not damaged. Tested the control knob and it functioned properly and recognized temp increases and decreases. Set the temp to 250 degrees and after 7 minutes was at an average of 250 at the center of the griddle and 180 degrees on the edges. Set the temp to 300 degrees and after 15 minutes was at an average of 300 at the center of the griddle and 250degrees on the edges. Set the temp to 350 degrees and after 25 minutes the unit was running away with the temp. Temp in the center was 455 degrees at the center and 340 degrees at the edge. As I continued to run the cycle it would randomly spike in temp. Turned the temp setting down and the control would drop in temp than quickly jump back up. Customer had a lightning strike recently and it now affecting the temp controls on the unit. Found a similar control issue with back burner. Found an inconsistent short in the electrical, This presents a safety hazard for the customer, and not repairable. Tech recommends to replace the unit due to temp control safety issues."

"Inspected the unit and could hear a loud grinding noise. Disassembled the unit and found the glides and felt need to be replaced. Replaced glides and felt and ran a test cycle. All checks OK, no abnormal sounds during the cycle.; used 2 WE1M504 (Slides), 2 WE1M1067 (Glides), and 2 WE9M31 (Felt) from stock"

Installed evaporator fan motor, checks okay

Installed new filter housing and unit checks ok

Replaced parts, checks okay

Fresh food fan is not circulating the air ; used 1 WR60X26866 (Ff) from stock

Installed new evaporator fan and defrost heater.

"Found loose connection at drain pump, repaired connection, unit checks ok. User interface had cosmetic issue that was not covered by AHS."

"Customer claims the unit not cooling intermittently, tested unit, found all operations check ok."

"Found unit giving orange flame on every burner intermittently, called LG Techline, they suggest replacing the regulator. Part needed is no longer available."

"Installed new control and user interface, unit checks ok."

"Found control not sending voltage to drain pump or inlet water valve, overflow switch stuck open, will need control and switch replaced. Customer considering repair."

Inspected unit and found an E01 error code on the display. Had customer turn off breaker for about 30 seconds and turn it back on. Was able to start and run cycle. Told customer that she could pay for the service charge right now and it is good for 30 days so if she continues to have this problem she can call in and I can get the control board ordered for her.

"Customer claims that cycle taking too long to dry clothes, again I told them that they have a blockage in the vent, unit checks ok."

"Installed new timer, unit checks ok."

Inspected unit and found wire going to heating element burnt and broken off. Stripped down wire and replaced terminal. Ran tests all checks OK.

Installed new magnetron and thermostats. All checks ok.

"Inspected the unit and found the icemaker not functioning, found water leaking out underneath the deli drawer due to the evaporator cover and fan not functioning caused by the drain line in the fresh food section to clog up, also found the fan in the freezer section not running. Found two of the buttons on the front display panel not responding or entering diagnostics. Checked temperatures in the fresh food section and they were an average of 35? and an average of 18? in the freezer section. The unit will have to be defrosted for 24 hours before we can install parts. Requesting autho to order parts. ; ordrng 1 WR02X12669 (Mullion), rqstng P&A on 1 WR13X10658 (Evap cover assembly) and 1 WR02X12603 (Heater) and 1 WR17X12467 (Freezer evap and cover) and 1 WR13X10660 (Display) and 1 WR30X10097 (Icemaker)"

"Spoke with the customer and they want us to order the parts needed. Ordering parts. ; rqstng P&A on 1 W11297461 (Heater and fill tube) and 1 W11482025 (Water valve), states that autho needed"

Needs convection fan and main control. ; ordrng 1 ##### (Convection fan) and 1 #### (Main control)

Fan frozen up and control board not defrosting properly; ordrng 1 5304523725 (Tower) and 1 5304523722 (Fan) and 1 5304523741 (Fan) and 1 5304529281 (Cont brd)

Ice maker not advancing properly, ice maker in freezer fill tubes leaking. Replaced ice maker ; ordrng 1 5303918602 (Tube) and 1 5304508046 (Insulate) and 1 243297613 (Imk)

Replaced parts, checks okay

Fresh food fan is running intermittently ordering a new one; ordrng 1 WR60X29099 (Ff fan)

Damper motor is locked up ; ordrng 1 W10151375 (Damper)

Unit freezing up. Needs two days shut down before return visit. ; rqstng P&A on 1 DA92-00384L (Control) and 1 DA97-12609C (Cover)

Unit making noise while in spin. Testing unit. Unit pump is rattling as well as motor assembly. ; rqstng P&A on 1 AJB76315004 (Stator) and 1 4040FR4051C (Screw) and 1 AHA75693425 (Drain pump) and 1 EBR86771815 (Main pcb)

Unit popped and flashed error codes. Burners not working. Needs several parts for repair. Customer saw a flash and turned unit back off at breaker. Unit sparked and flashed. Not operating correctly. ; rqstng P&A on 1 1111 (Control) and 2 387404866 (Burner)s and 1 387404759 (Burner) and 1 387761248 (Burner) and 1 5304516862 (Relay) and 2 5304527384 (Generator board)s

Inspected unit and found a stain in the front of the freezer from water leaking out. Water leaking from underneath the unit. Did not find any ice buildup on the inside or along the drain line. Ordering drain pan and drain pipe.; rqstng P&A on 1 5304521531 (Drain pan) and 1 5304521530 (Drain pipe)

"Doors not closing correctly; rqstng P&A on 1 241761301 (Hinge) and 1 241761302 (Hinge) and 1 FR241918001 (Hinge) and 1 FR241918004 (Hinge) and 2 FR241917801 (Closer)s, states that autho needed"

Inspected unit and found icemaker motor humming like it was going to cycle but the arm staying in the same spot. After about 10 minutes icemaker was extremely hot to the touch. Explain to customer that ice maker will not fill with water if it cannot cycle. Ordering icemaker. ; ordrng 1 AEQ36756919 (Ice maker)