Inspected unit found right side spring had come off reinstalled spring and then noticed the main power line feeding the unit was damaged and the line was too short. Turned off breaker and advised customer to have an electrician come out and install a longer line and not to use the unit until the line was repaired.

Installed parts listed, all checked good

Called techline spoke to Mike to raise left door to close properly

Adjusted fill tube and checked good

Adjusted the air tower and checks ok

Installed parts listed, all checked good

Installed parts listed, all checked good

Installed parts listed, all checked good

Unit has a sealed system non repairable

Replaced both ice makers and reset unit

Inspected the unit and found that the hot water valve was turned off. Turned on valve. In a test cycle. All checks OK

Inspected the unit and found a failed cycling thermostat. Replaced with truck stuck. Ran a test cycle. All checks OK ; used 1 D504515 (THERMOSTAT) from stock

Inspected the unit and found a failed gear case and a water valve. Customer declined repair.

Inspected the unit and found that all the waterlines to the fridge were corroded and cracked in half. Customer thought that the water was off to the fridge. But upon a series of tests found that the water valve was not shutting off properly. Customer will need a plumber to secure the repair.

Inspected the unit and found that the unit was failing to go through a defrost. Customer declined repair.

Inspected the unit and found a failed control. Part has been discontinued and is no longer available.

Inspected the unit and found a failed shift actuator. Customer declined repair.

Inspected the unit and found a failed communication between the control and motor. Customer declined repair.

That it was in need of a complete rebuild due to overheating from seizing up in the transmission. Customer declined repair.

Inspected the unit and ran a test cycle. Found the unit heating up correctly on three different cycles. Clean the moisture sensor bars and check. Check for good voltage. All checks good.

"Inspected the unit and the belt and drive motor for any burning or smells. Installed the new parts. Ran a diagnostic cycle and the unit filled with water and drained, also it agitated, and spun to correct speed. All checks good"

"Inspected the unit and found the turntable, making a noise while turning. Removed the tray and the rollers out and clean the rollers off and cleaned any food on the bottom of the microwave. Reinstalled the tray and rollers and found no noises. All checks good."

Inspected the unit and found some odors coming from the dishwasher. Found some food down at the bottom of the drain and that the drain line did not have a high loop in it. Adjusted the drain hose and clean the drain filter. Advise the customer to run some cleaning tablets to help break up any smells or bad odors inside the unit. All checks good

Inspected the unit and found the unit not draining. Remove the drain filter and found large amounts of the backing of a rug in the drain filter. Cleaned the filter out and chop vac the rest of the rug out. Test cycle. All checks good.

Inspected the unit and found that the dishwasher was pushed too far back and pushing on the power cord and causing it to kill power to the unit. All check good file 87593333

Installed parts listed, all checked good

Install the new water valve and ran a test cycle. All checks good.

Tested unit and tried to run a cycle and the display board started acting strange and the unit would not turn on. Determined the display board needed to be replaced. Ordering parts.; ordrng 1 W11401710 (Board) and 1 W11135391 (Display)

Rebooted control board and unit came back on or a new control board. ordrng 1 WPW10743957 (Cont brd)

Installed new control board and water valve and returning the core part; ordrng 1 W11614224 (Compressor)

Inspected the unit and found the lid broken due to not normal wear and tear. Customer attempted to repair it without success. Ordering parts. ; ordrng 1 W11259006 (Lid) and 1 WP8563965 (Hinge) and 2 W11404293 (Screw)s

"Inspected the unit and found the unit not heating and not responding. Found that the transformer had blown and the magnetron had stopped working due to the liner, starting to fade and caused the magnetron to spark, and blow itself. Unit will need to be replaced ; ordrng 1 6324W1A001L (Magnetron) and 1 EBJ60664610 (Transformer) and 1 0CZZW1H004B (Capacitor) and 1 6930W1A003D (Thermostat) and 1 ACM74119055 (Controller) and 1 ADQ75393201 (Noise filter)"

Inspected the unit and found the turntable. Not turning and found a couple buttons on the control board not responding. Unit is 20 years old and located in the kitchen. Ordering parts. ; ordrng 1 5304408980 (Turntable motor) and 1 5304424537 (Control board)

Inspected the unit and found the unit not heating. Ordering parts.; ordrng 1 W10703867 (Heating element) and 1 W10875442 (Control board)

Installed parts listed, all checked good

Ran a few test cycles on the unit and all mechanical functions were working well. We did see a lot of suds left over and determined after investigation that there was no high loop and also rinse aid had not been used in quite sometime. Recommended the customer use detergent without dawn dish soap and to use rinse aid regularly. Cleared suds. Ran a cycle with veg oil as we left to help clear any other suds.

"Inspected the unit and found the adjusters were damaged, installed new adjusters and all checks ok.; used 1 W10712394 (RACK ADJUSTERS) from stock"

Installed parts listed, all checked good

Inspected unit and found that the ice tray on the dispenser had some damage. Had part on truck and installed. All checks good; used 1 W10873791 (ICE MAKER) from stock

Installed parts listed, all checked good

Inspected unit removed from wall checked connection and we had good voltage. Determined that the control board needed to be replaced. Photos attached found damage to cavity liner and its not repairable. Called AHS and advised of issues. 100KMML

Inspected the unit and found the oven lights not responding on the MW. Reset the unit and board. Lights functioning now.

Found a failed element. Installed part. All checks ok. ; used 1 8544771 (ELEMENT) from stock

Installed parts listed, all checked good

Adjusted freezer door and cleared out ice and checks ok

Installed new fan motor and reset unit

Installed new door and checked OK

Inspected the unit and found that the inner spin basket welds completely broke off the bracket. Customer will need an inner spin basket out of tub and suspension. Parts have been discontinued and are no longer available.

Installed part. All checks ok

Inspected the unit and found that the lid lock was in need of adjusting. Tightened hose adjusted door lock. Ran a test cycle. All checks OK

Installed part. All checks ok

Inspected the unit and found a squirrel lodged in the blower wheel. Removed squirrel. Ran a test cycle. All checks OK

Installed parts. All checks OK

Installed part. All checks OK

Inspected the unit and found that all suspension needed rebuilt. Removed and rebuilt all 4 suspension dampers. Ran a test cycle. All checks ok

Inspected the unit and found a failing control. Customer declined repair

Inspected the unit and found the unit not starting. Checked the unit for good voltage and we had 240v. Removed the back cover and found a bad connection on the bullet fuse. Made adjustments and all checks good.

"Inspected the unit and found the door, bent and not opening properly and getting caught on the inter latch. You have to lift the door to get the door to open properly. This is not normal wear and tear. Something caused the door to open past its stopping point and will not close properly due to bent door hinges. Auth #402CTAI"

Installed the new door switch and ran a test cycle. All checks good

Inspected the unit and found the unit not making good connection on the display board. Made adjustments to the display board to help with any connection issues. All checked good.

Installed parts listed, all checked good

Inspected the unit and found the hot water valve not working and dispensing water. Replaced the water valve and ran a cycle. The hot and cold water are both working. All checks good.; used 1 W11165546 (WATER VALVE) from stock

"Inspect the unit and found the left door not closing all the way and the mullen flap not opening. Made adjustments to the door and the door is closing and opening properly. All checked good."

"Inspect the unit and found the unit taking a long time to preheat. Replaced the bad igniter and ran a test cycle, all checks good; used 1 5303935066 (IGNITOR) from stock"

"Installed board and recalibrated the unit. During the recalibration you could hear a grinding noise and the unit shut off. Reset the unit and could not get it to power back up. Removed top panel and found the board receiving 120v but sending no voltage out. Pulled the unit forward and inspected the underside. After removing the motor guard found grease on and around the gearcase. Faulty gearcase. Called techline while checking for possible wiring short to motor, drain, and acuator. Found no short or damage. Techline answered and I advised of the issues. They checked the control and display board and advised the display board has shorted out. Tried a few resets on the wiring and board with no response. Techline advised they do not know what has caused the board to short out again but recommended replacing the display, main wiring harness and DC voltage components as something is causing it to short out. Unit is only 3 years old but will need a complete rebuild of the unit, additional labor, time and tech. Not a recommended repair. ; ordrng 1 W10721967 (Cam kit) and 1 W11239857 (Belt) and 1 W10752187 (Screw) and 1 W11395618 (Capacitor) and 1 W11481722 (Acuator) and 1 W11399437 (Drain) and 1 W11449840 (Gearcase) and 1 W11551646 (Nut) and 1 W11405458 (Harness) and 1 W11178145 (Harness) and 1 W11238377 (Pump meter) and 1 W10752283 (Washplate) and 1 W11178224 (Basket) and 1 W11219115 (Tub) and 1 W11478523pw (Facia)"

Ordering parts; ordrng 1 W11024089 (Fan)

Inspected the unit and found a failed tub assembly. Ordering parts. ; ordrng 1 204690note (Belt) and 1 39837 (Balance ring) and 1 719P3 (Spin basket) and 1 39122 (Gasket) and 1 766P3A (Hub kit) and 1 203851 (Drive bell) and 1 203852 (Agitator) and 1 203968 (Tub cover) and 2 200996P (Sealant)s and 1 204383 (Outer tub kit) and 1 39253 (Bearing assembly)

Inspected the unit and found a failed control system due to a shorted pump. Ordering parts.; ordrng 1 W11725661 (Control) and 1 W11335100 (Harness) and 1 W11259498 (Pump) and 1 W10808317 (Belt) and 1 W11414731 (Latch assembly)

Inspected the unit and found the unit when closing the door is blowing the breaker. Made adjustments to wires and when starting a cycle it will run for about 10 seconds and then both breakers again and the unit is not heating properly. Ordering parts. ; ordrng 2 W10269458 (Micro switch)s and 1 W10686543 (Control board) and 1 W10733412 (Transformer) and 1 W10727360 (Micro switch) and 1 W10626122 (Magnetron) and 1 W10672720 (Control panel)

Inspected unit and discovered some debris on the wheel spindles that was causing some noise coming from the felt pads. Disassembled and cleaned up the pads and added grease to the spindles. Also cleaned out the blower housing that had some excessive buildup. Put unit back together and ran test cycle. All checks good.

Installed new water valve and freezer door gasket

Installed new relay and compressor and filter drier and unit checks ok

Airtower and damper not sealing properly ordered parts to be installed ; ordrng 1 5304530963 (Evap fan cover) and 1 5304532941 (Damper) and 1 5304530941 (Seal)

Found everything functioning as it should from factory upon arrival. All checks OK

Installed door. All checks OK

Inspected the unit and found a failed bake element and a failed infinite switch. Customer declined repair.

"Inspected the unit and found that it was in need of a suspension system. And that the feet were all rusted off. Warranty company has put it in for replacement."

Inspected the unit and found a failed belt. Replaced with truck stock. Ran a test cycle. All checks ok; used 1 W11239857 (BELT) from stock

"Installed the new control board and ran a test cycle, all checks good"

Installed the new parts and ran a test cycle. All checks good.

Inspected the unit and found the rails on the side of the bottom drawer on the right side was not attached to the drawer. Ordering bottom drawer; ordrng 1 5304528242 (Bottom drawer)

Installed all the new parts and ran a test cycle. As soon as we turned the convection bake on it blew the new relay board. Talked with GE tech line and showed them several pictures of the relay board to make sure it was wired correctly and the unit was wired correctly. Waiting to hear back from GE on what they want to do. case #13996212

"Inspected the unit and found the door boot was torn and causing water leaking from the front. The torn door boot is not something that is covered by warranty due to outside objects tearing the door boot."

"Inspected the unit and found the customers complaint was that there was water leaking. Put the unit into diagnostics and ran several cycles and a drain cycle and found no leaks. Tilted unit back and looked for hoses that had come loose or were not attached properly. All checks good."

"Inspect the unit and found the customer stating that there was an L2 error code. After running a diagnostic cycle, found several issues happening with the unit where the motor would not spin up to full speed and would stop during full speed. Also did not hear the drain pump kick in at all. Informed the customer of the cost of a control board and that it could have wiring issues due to an L2 error code. And customer does not want to put that amount of money into the unit."

Installed the new freezer door and inspected the door gasket to make sure it was sealing properly. All checks good.

"Inspected unit and noticed debris in filters, removed filters and cleaned thoroughly and reinstalled. Ran several test cycles and detected no leaks."

"Inspected the unit and found a large amount of vibration coming from within it. Removed top, front door, all brackets, removed drum and belt. Found a large amount of lint to one side of the blower wheel housing. Removed all lint. Greased support wheels. Reassembled. Ran a test cycle. All checks OK"

Installed new wiring harness and ice maker and control panel and reset unit

Installed 4 suspension rods and calibrated unit, all checked good

Installed parts listed, all checked good

Inspected the unit and found the control locked up and not responding. Found a toothbrush down in the blower housing wheel. Removed debris and reset the control board and cleared lock. Ran a test cycle and all checks ok.

"Inspected the unit and noticed the control board was shutting down the unit. Ran a test cycle and could hear abnormal noise inside the unit from support wheels, idler pulley and blower wheel. Ordering partsUnit is 6 yrs old; ordrng 1 DC92-01624M (Control) and 1 DC67-00180B (Blower wheel) and 1 6602-001655 (Belt) and 4 DC97-16782E (Support wheels)s and 1 DC96-00882F (Pulley)"

"Upon arrival knob on dryer was hard to turn, upon further inspection saw that the knob connection had a small crack. Also the timer needed to be replaced. Informed customer of the required repair and parts. Customer refused due to the cost of the repair."

Tested all burners on cooktop all burners light up fine with a nice flame height. Tested broiler cycle and it worked fine. Checked the glow igniter on oven and it lit the oven up and the oven got up to proper temperature and the igniter continued to run as it should. Customer concerned about an abnormal sound and smell. Customer claimed would not heat up. Technician could not find anything wrong at the time of service.

Inspected the unit and found that the connector had fallen off of the solenoid. Made necessary adjustments to the solenoid and connector. Secured all connections. Ran a test cycle. All checks OK

Inspected the unit and found a failed heating element. Replaced element with truck stock. Ran a test cycle. All checks OK ; used 1 D510329P (ELEMENT) from stock

Ice room door not sealing properly ordered new door ; ordrng 1 W11268536 (Ice room door)

Inspected the unit and found a failed control. This part has been discontinued and is no longer available.

Installed 3 way valve and reset unit and checks ok