Adjusted refrigerator temperatures and dampener door. Unit checks OK

Installed parts listed all checked good

"Inspected the unit and found the pressure sensor hose not completely secured to the outer tub basket and leaking. Secured the hose and ran a diagnostic cycle, found no other defects with the unit. Ran a quick wash cycle and found no other leaks. All checks ok."

"Installed parts, all checks ok"

Attached hose. All checks OK

Installed parts listed all checked good

Customer states that the unit is leaking water into the fresh food section and below. Water is coming from a clogged defrost drain. Cleared ice and cleared drain. Verified drain is open. All ok

"Customer states that the upper icemaker is noisy and will not produce ice. Forced icemaker to cycle, the motor is stripped, causing the noise. Evaporator fan for the icemaker is running. Forced icemaker to fill and it would not fill. Inspected further and found water line froze. Unit needs icemaker and waterline. Installed new ice maker and water line. Cycled ice maker and it is operating as it should. All ok. ; used 1 241920106 (Fill tube), and 1 243297613 (Ice maker) from stock"

Installed new drain pump and ran to test. Unit is operating quietly. All OK.

Installed filter dryer pressurized the system and captube broke. Called techline spoke to Gaety case# 86592049

Installed new filter housing and checks ok

Installed new switch tested good.

Installed new door switch tested good.

"Inspected the unit and found the bake, convect, and broil element activating and heating properly. Ran the unit to 350 degrees and it preheated to an average of 360 after 15 minutes (365 on sides, 390 on top, 360 on back and 345 on bottom). Recalibrated the temperatures at -10? and demonstrated how to do this for the customers they can make any calibration changes in the future. All checks OK"

"Installed parts, all checks ok"

"Installed part, all checks ok."

Inspected unit and found a large amount of gunk buildup in the filter assembly. Unit not completing the cycle to heat dry. Advised customer use cleaning tablets on a regular basis. Refilled rinse aid dispenser. Removed the filters and cleaned them. All checks OK.

Inspected the unit and found a failed communication between control and display. Customer declined repair

Inspected the unit and found a failed a icemaker/control. Customer declined repair.

Inspected the unit and found a failed door lock and control. Customer declined repair.

Inspected the unit and found that the basket broke loose from the gearbox. Customer declined repair

Replacing ice maker wasnt advancing properly ; used 1 DA97-07603B (Imk) from stock

Installed control board and updated the software

Adjusted doors and instructed customer about styrofoam in the air tower

Inspected the unit and found a sealed system leak. Customer declined repair.

Inspected the unit and ran unit through multiple test cycles. Everything is functioning as it should from factory. Could not manifest any unusual noises. All checks OK

Installed part. All checks OK

Ran tests found unit has sealed system leak causing no cool; ordrng 1 5304532111 (Evap) and 1 5304519758 (Compressor) and 1 5303305677 (Dryer)

Inspected the unit and found a faulty turntable motor. Ordering part.; ordrng 1 5304513471 (Motor) and 1 5304533653 (Control)

Unit has two error code one for motor control fault and the other control board fault. Unit needs a new motor and control board. Basket is spun by hand. It is very loud. You can also needs a new gearcase and inner basket.; rqstng P&A on 1 W11454734 (Gearcase) and 1 W10890624 (Motor) and 1 W10752719 (Basket) and 1 W11417466 (Control)

Installed new parts. All checks ok.

Installed new parts. All checks ok.

Ice maker is locked up ordered new one to be installed; ordrng 1 Aeq73110219 (Imk)

Ice room fan not blowing properly ; ordrng 1 W10846539 (Fan)

Ice maker and control board not communicating properly ; ordrng 1 243297608 (Imk) and 1 5304529532 (Main brd)

Control board not going into defrost properly, ordered new control board; ordrng 1 W11664342 (Control brd)

Ice maker is not correct ordered new ice maker; ordrng 1 AEQ73110219 (Ice maker)

Ran tests found element shorted out falling against drum causing no heat and noise; ordrng 1 137392700 (Element)

"Ran tests found drive and inner basket bad causing out of balance loads and extreme noise, customer does not wish to move forward"

"Installed new part and now ui did not work. When putting the old one back on, the unit is now giving a er ce code for miscommunication. Also found the door was dented around user interface. Ordering parts. ; rqstng P&A on 1 5304526865 (Control board) and 1 5304527031 (User interface (PW)) and 1 5304527003 (Freezer door)"

Inspected unit and found fresh food section not cooling properly. Found evaporator at proper temp. Plugged newfi into unit and tried to run evaporator fan. Fresh food evaporator fan did not run. Ordering part. ; ordrng 1 WR60X26866 (Evaporator fan motor)

Ordering part. ; ordrng 1 DA96-00640A (Flex zone wire harness)

"Checked unit over, found that the unit would not run through a spin cycle. Cleaned pressure switch and reset control. Reprogrammed control board and I was finally able to get the unit to run through a spin cycle. I informed the customer if this did have future issues, it would need a new control board and potentially a pressure switch."

"Checked unit over, found that the unit was not heating up. Found that the power cord and terminal block had shorted and it was not making a good connection. Removed wires and cleaned terminals. Replaced terminals on power cord. Reassembled unit checks OK"

Checked unit over found the idler had come loose and the belt had come off. Reinstalled idler and belt. checks ok

Checked unit over found the unit was not heating up or running. Disassembled unit repaired harness for thermal fuse. Checked timer and heaters. Checked door switch. Informed customer they need to have the vents cleaned out. Reassemble unit. Checks OK.

Replaced door seal. Checks ok

Cleared pressure switch and reprogrammed unit. Errors for door lock and pressure switch.

Installed parts listed, all checked good

Reset control and reprogrammed and cleared suds. Checks ok

Checked unit over and found that the unit had a broken wire to the door switch. Repaired wire. Checks OK

Cleared out drain checks ok

Fixed door latch checks ok.

Replaced icemaker checks ok.; used 1 DA97-15217D (ICE MAKER) from stock

"Installed the part, all checks OK"

Installed parts listed, all checked good

"Inspected the unit and ran a mechanical test. Unit filled with water, activated the wash motor on low and on the high setting, activated the float switch, activated the lower and upper sprayarms on low and high cycle, activated the dispenser door and rinse aid dispenser, and activate the drain pump. Found no mechanical defects with the parts listed. Enter diagnostics to test for software issues and found multiple error codes that were not accurate in the description of the problem. Some error codes shown are not even programmed for this unit. Possible software issues on the control board. Reprogrammed the control board using latest approved software. Ran two more test cycles in unit is functioning properly at this time. The customers using cascade detergent pods with dawn dish soap and I recommended they use a different detergent that does not have Dawn dish soap, as these often suds up and will cause issues with the sensors. The manufacture is currently recommending not to use the detergent pods with Dawn dish soap. Also recommended to place any detergent pods down in the bottom of the tub rather than placing them in the dispenser door to get a more effective wash cycle."

"Installed parts, unit still not responding properly and not entering diagnostics. Unit keeps shutting down while trying to recalibrate. Contacting AST regarding issue. AST submitting the unit to replacement options."

Customer states that unit leaks when draining. Leaking from the left side near the drain hose. Inspected underneath the unit and found the drain hose loose from the cabinet. It is leaking when the pump drains. Secured hose with clamp and ran to test. No more leaks. All ok.

Customer states that the unit will not start. Lights up but wont do anything else. Unit is full of water as well. Cleared water and verified correct voltage. Outage is good. Forced unit into drain but it wouldnt drain. Drain hose is clear and plumbed correctly. Inspected further and found the float switch stuck open. Freed switch and unit is operating correctly.

Installed all provided parts and verified correct operation. All ok. Unit operates as it should.

Cleaned out pressure switch and cleaned out water valve. Reprogram control board. Tested unit in unit is now filling with the proper amount of water. Customer has more issues and he will need a new water valve.

Dispenser tubing wasnt in position adjusted and checks ok

Installed new compressor and dryer recharged unit told customer to give it 24 to 48 hours to get down to temperature

Ran tests found air tower gasket rolled over causing air leak causing return to freeze up causing leak. Installed new gasket cleared ice tested good.; used 1 5304530941 (Gasket) from stock

"Ran tests found latch spring came off, rehooked spring unit works fine."

"Ran tests found ui not turning on power to control good , cleaned connections to ui unit turned on started heated and tested good. Turned off and on severs times unit seems to be working normally."

Installed parts listed, all checked good

Inspected the unit and found the spring had came detached from the plastic clip for the door. Remove door cover and made adjustments to the spring attached to the metal bracket. All checks OK

Inspected the unit and found an odor coming from inside the unit. Ran a test cycle and found a large amount of suds in the tub. Added olive oil to the tub and continued running a cycle to help breakdown the suds. Recommended the customer use cleaning tablets regularly. All other checks ok.

Inspected the unit and found that the wrong orifices were in the middle burner. Replaced with correct orifices. All checks OK

Inspected the unit and found a failed icemaker. Replaced icemaker with truck stock. Ran a test cycle. All checks OK ; used 1 W11579560 (ICE MAKER) from stock

Inspected the unit and found everything functioning as it should from factory. All checks ok

Inspected the unit and found everything functioning as normal. All checks OK

Inspected the unit and found a failed thermal cut off fuse. Replaced fuse with truck stock. Ran a test cycle. All checks OK ; used 1 3390719 (FUSE) from stock

Unit has wiring issue in the cabinet and is nonrepairable. Called Neal and explained issue

Adjusted doors mullion wasnt closing properly

Inspected the unit and found a failed belt. Replaced belt with truck stock. All checks OK ; used 1 341241 (BELT) from stock

Inspected the unit and found a failed door switch. Replaced door switch with truck stock. Ran a test cycle. All checks OK ; used 1 W11427601 (Door switch) from stock

Inspected the unit and found a failed icemaker. Replaced icemaker with truck stock. all checks OK ; used 1 W10882923 (ICE MAKER) from stock

Installed parts. Ran a test cycle. All checks OK

Inspected the unit and found a failed control board. Customer declined repair.

Inspected the unit and found everything on the dishwasher was functioning as it should. But they had a slow drain. Customer will need a plumber to replace drain line.

Customer states that the dryer wont start. Voltage to the unit is correct. Motor hums when it is trying to start. No loose connections or broken belt. Motor is shorted. Motor will start if the drum is turned by hand. Unit needs motor assembly. ; ordrng 1 DC93-00101U (Motor assembly)

Unit is 10 years old in kitchen. Customer states that the unit is not cooling. Unit is currently unplugged. Removed back panel to inspect. No signs of visual damage to the compressor or the control board. Plugged unit in and the both the evaporator and condenser fan came on. There is no voltage going through the compressor from the main control board. Compressor windings are good. The unit needs control board. There may be more issues with the sealed system that we are currently unable to test.; ordrng 1 WR55X10942C (Main Control Board)

Customer states that the unit is building up frost in the freezer. Frost is along the top. Inspected the freezer door and found the door not sealing well. Adjusted the door and it is sealing well. The interior light is not working now. The control is not sensing the door open. The door switch is shorted closed from moisture. Unit needs door switch and LED assembly. ; ordrng 1 5304520495 (Door switch) and 1 5304530714 (LED)

"Controller assembly shows that it comes with a display but it did not. I need to order the display.; rqstng P&A on 1 EAV64012007 (Display), states that autho needed"

Inspected unit and found the ice maker not harvesting correctly. Found the ejector fingers loose from the motor. Replaced ice maker. All checks ok. ; used 1 DA97-07365G (ICE MAKER) from stock

"Customer was concerned about loud banging noise coming from washer. Ran unit through an automatic test cycle. Found cold water valve at the house not fully open. Advised customer that without the valve fully open there would not be enough water pressure to fill the tub properly, especially in a rinse when it uses only cold water. Informed customer that if there is not enough water unit would get out of balance easier and could possibly bang against the cabinet. Customer to call back if unit makes any abnormal noises."

Installed parts listed, all checked good

"Ran tests found display digits not all working, right front burner bad causing hot cooktop light to stay on; ordrng 1 EAV64012008 (Led displ) and 1 MEE62704901 (Burner)"

Ran tests found control not sensing temps causing unit to run all the time.; ordrng 1 DA97-08118E (Ui) and 1 DA41-00669A (Control)

Unit keeps crushing the ice. Ordering parts. ; ordrng 1 5304526872 (Ice container) and 1 241675705 (Solenoid) and 1 5304527039 (Motor)

Inspected the unit and found the appliance not responding and completely dead. Found unit receiving proper voltage but nothing responding to no lights on the unit. Disconnected the unit from power for several minutes and plugged it back in. Compressor started making a loud thumping noise and the fans activated inside the unit but neither the lights or the touchpad started functioning. The compressor is very warm to the touch and is locked up. The unit is 12 years old and located in the kitchen. Not a recommended repair. ; ordrng 1 WR55X11098 (Control (nla)) and 1 WR55X11100 (UI) and 1 WR49X10283 (Inverter) and 1 WR87X10111 (Compressor)

Inspected the unit and found the display board not responding consistently. Ordering parts. ; ordrng 1 EBR82427001 (Display board) and 1 AGL73093122 (Display panel)

"Customer states that the unit wouldnt start and now it wont power on. Voltage to the unit is correct. User interface has signs of shorting out from moisture. Not getting the 5vdc to the user interface from the main control. After resetting the control I was able to get it to power on. Checked control for errors. Found F5E2 lid lock error, F6E3 communication error, and F6E2 communication error. Lid lock is testing as open. Unit needs the main control, user interface, and lid lock assembly. Unable to test spin or agitation because the lid wont lock. ; ordrng 1 W11112662 (User interface) and 1 W11417461 (Main control) and 1 W10861642 (Lid lock)"

Inspected the unit and found a locked compressor due to a sealed system leak. Ordering parts. ; ordrng 1 WR87X41647 (Compressor) and 1 WR86X37550 (Die dryer)

Inspected the unit and found a failed craft icemaker. Ordering part. ; ordrng 1 AE073449901 (Craft ice maker)

"Checked unit over, found that the unit will not produce ice. Found the icemaker was frozen. Removed icemaker and cleared out ice buildup. Also found that the fill line for the icemaker was frozen. Removed fill line for icemaker and cleared out. Reassembled unit. Instructed Customer to give the unit 24 hours before it starts making ice."

Reset and reprogrammed control. Checks ok