Speed Queen Washer Error Codes: Causes & Solutions

While no one likes to see an error code blinking on their washing machine display, these codes are actually helpful if you know how to read them. They aid in pinpointing exactly what problem your washer is experiencing, which makes fixing the issue quick and easy. While some error codes indicate a hardware issue or something that requires a technician, many have surprisingly simple DIY solutions. This guide breaks down the causes and solutions to some of the most commonly seen Speed Queen error codes. Read on to find out what to do!

This guide applies to the majority of common Speed Queen washers, including the following models:

AA3410

AA4410

AA4411

AA5420

AWN311SP111TW01

AWN402PP111TW01

AWN432SP113TW01

AWN432SP113TW04

AWN542SP111TWAH

AWNE82SP113TW01

AWNE92SP113TW01

AWS01NW

AWS44NW

AWS48NW

AWS51NW

AWS52NW

Before You Start

Any time your washer displays an error code, it’s a good idea to try resetting the appliance before you attempt any further repairs. Sometimes a power surge or software glitch can cause your washer to display an error code when there’s no underlying problem. In these cases, resetting your washer will get it up and running again without the need to take any further action. 

To reset:

• Disconnect your washer from its power source. 
• Leave it unplugged for at least three minutes to allow all the components to fully discharge. 
• Plug the washer back in. 
• Run a test cycle (make sure it’s the same cycle that was running when the error code first appeared). 
• If the error code doesn’t come back, your washer is likely fine. If the same error code comes back, there’s an underlying problem that needs to be fixed. 

Error Codes: Er. dr, Er FL, Er nF, Er. PS

Meaning: There’s a fault with the water level

Fix: Check whether both the hot and cold faucets are turned all the way on and ensure that the hoses aren’t kinked or obstructed in any way. If the hoses appear fine, try turning off the water and disconnecting the hoses, then thoroughly clean the filter screens. Once the screens are cleaned, turn off the washer for three minutes, turn it back on, and then test to see if it’s functioning normally. 

Error Code: Er. dll

Meaning: Door won’t unlock

Fix: This error is usually due to a glitch and is easily cleared. Simply unplug your washer for three minutes to reset, then plug it back in. The door should now open as normal. 

Error Code: Er ub

Meaning: Unbalanced load

Fix: This error commonly occurs when your load is too heavy or when you’re washing large items such as blankets. To fix the problem, ensure you always follow the Speed Queen recommendations for load size in your model of washer. If you need to wash large, heavy items, make sure you select a slower spin speed as this reduces the chance of the load becoming unbalanced. 

Error Codes: E Ht, E:HT, E:Ht

Meaning: Heater problem

Fix: The heater circuit needs to be replaced. Unless you’re a qualified technician, it’s best to get a professional to do this. 

Error Code: CLoSE door or do

Meaning: Door is open

Fix: Ensure the door is properly closed. If it appears to be closed properly, the door switch may be faulty and need to be replaced. 

Error Codes: E dS or Er, dS

Meaning: Voltage issue

Fix: This indicates that the voltage is incorrect. Ensure the washer is plugged into an outlet with the correct voltage or get an electrician to check your wiring. 

Error Codes: E Sd, Er, Sd, ESd

Meaning: Slow drainage

Fix: The water is draining slower than it should, which could indicate an issue somewhere in the drainage system. Clean out the filter and check the drainage hoses for clogs. 

Error Codes: E SudS or Er, SL

Meaning: Excess suds

Fix: This error occurs when suds remain in the washer after all sud removal steps in the cycle have completed. This is usually due to too much detergent being used or the wrong kind of detergent being used. Try leaving the suds to dissipate for about an hour, then run a rinse cycle to get rid of the remaining suds. To prevent the error from occurring, make sure you use a high-efficiency detergent brand designed to produce fewer suds, and always use the recommended amount. 

Error Codes: E Ld or Er, LE

Meaning: Water leak

This error appears when you run the water leak detection cycle if you suspect there might be a leak somewhere in your machine. If this error code shows up, you should immediately seek professional help as a water leak can cause damage to your home. 

Error Codes: E d 22 or Ed, 22

Meaning: Motor temperature too high

Fix: If the motor temperature gets too high, it usually means that your washer is overloaded or there’s too much friction when the drum spins. Try manually spinning the drum to see if there’s too much resistance. To repair this issue, you may have to replace the bearings or, in some cases, the motor itself. 

Error Codes: E d 29 or Ed, 29

Meaning: Motor not connected 

Fix: If your motor isn’t connected or only partially connected, it may be due to damage to the motor harness. First, check that the harness is completely plugged in on both ends. Then inspect the harness for damage or wear. If the harness is damaged, it may need to be replaced to clear the error.