Installed new compressor and recharged unit and checks ok. Told customer to give it 24-48 hrs to stabilize

Installed parts listed, all checked good

Inspected the unit and found a frozen waterline to the dispenser. Customer will need to put the unit through a 24 hour defrost in order to clear all lines throughout the system.

Inspected the unit and found a failed door switch. Replaced with truck stock, ran a test cycle. All checks OK; used 1 3406107 (SWITCH) from stock

Inspected the unit and found it going through an emergency drain. Let it go through the process and then recalibrated the control. All checks ok

Inspected the unit and found everything functioning as it should from factory. All checks OK

Inspected the unit and found a failed defrost timer. Replaced with truck stock. All checks OK; used 1 5304526183 (DEFROST TIMER) from stock

Installed part. All checks OK

Inspected the unit and found loose wiring at the terminal. Secured all wiring. Ran a test cycle. All checks OK

Inspected the unit and found everything functioning as it should from a factory. All checks OK

Inspected the unit and found everything functioning as it should from a factory. All checks OK

Inspected the unit and found everything on the dryer functioning as it should from factory. With proper temperatures. Found that the vents were at about 50 to 60% airflow. Customer will need vents cleaned out to ensure adequate drying. All else checks ok

Check out the unit and the temperatures in the refrigerator were cooling and were sitting around 37?. Checked the freezer and the freezer was a little warmer but still freezing food and getting down to temperatures. While working on the unit did not hear the fan in the freezer kick on. Adjusted the temperatures for the freezer and the refrigerator to help get them down to cooling ranges. Advise the customer to give it 24 to 48 hours to see if if the freezer gets back to cooling temperatures. Check OK

"Checked out the unit and found the unit cooling and all the temperatures at the correct ranges. Customer stated that the fan in the freezer is making a loud noise and And the unit turned off for a day or so, and then came back on. Checked over the unit and found everything working the way it should be. Advise the customer to keep an eye on it, and to record any issues that they encounter of the next few days. Temperatures were in the correct ranges along with the defroster and drain tube being cleared. Checks OK"

Check out the unit and found when starting a cycle the unit is squealing. Disassembled the unit and lubricated all support wheels and idler arm. Reassembled the unit and ran a test cycle. Check OK; used 1 W10837240 (BRACKET (TS)) from stock

"Checked out the unit and found when running a drain cycle. the drain line is too high above the washer and when the drain pump tries to pump the water, it cannot pump the water all the way up to the standpipe. Lowered the drain line and the water pumped out fine. Advised the customer to see if they could resolve a situation on lowering the standpipe so the water can drain properly. Talked with the warranty and that is not something they will cover due to it working fine at the moment."

"Talked with Bosch support and they stated that the fabric softener is only dispense on certain cycles. Advised customer to try different cycles and see if that resolves the issue. Also if the issue is not resolved by different cycles, the unit unit would need to control board. Advise a customer of the cost and he did not want to proceed further."

"Check out the dryer and found that the drum was rubbing on something on the back of the unit. Removed the back cover, and the exhaust exchanger on the back. Found a screw that was put in the heat exchanger that was too long and dragging on the basket. Replaced the screw and reassembled the unit. Checks OK"

"Checked out the unit and found it not draining. Disassembled the unit and drained all the water out of it. Installed a new drain pump on the unit and reassembled the unit. Ran a test cycle, all checks good; used 1 4681EA2001T (DRAIN PUMP) from stock"

Upon arrival got customer concern about timer getting stuck in place and timer motor not advancing again. Called speed queen and spoke with Ed. He had me test the timer and everything tested well. He told me about turning the timer clockwise only and how the timer motor will not advance if a cycle is started when turned counter clockwise due to the contacts opening up. Explained everything to the customer. Customer to make sure she is turning timer clockwise always and to call back if there are further issues.

Installed parts listed, all checked good

Replaced leaking water valve. Checks OK ; ordrng 1 AJU75152601(ts) (Valve)

Needs new control and display ; ordrng 1 W11158457 (Control panel) and 1 W11133021 (Control)

"Checked unit over and found that the rear bearing and drum had failed. Also, the front support has failed. Unit is about 18 to 20 years old located in the laundry room. Model and serial tag is readable.; rqstng P&A on 1 #### (Drum), ordrng 1 #### (Front support)"

"Unit needs new gearcase, basket and agitator. Motor is burnt up due to locked up transmission. Also not filling with proper water due to control issues. Unit 3-5 years old in the laundry room ; rqstng P&A on 1 WH22X38441 (Control) and 1 WH45X26174 (Inner basket) and 1 WH03X33729 (Gearcase) and 1 WH43X30957 (Agitator) and 1 WH03X29559 (Motor), states that autho needed"

Installed parts listed, all checked good

Installed parts listed, all checked good

Installed new control board and checked good

Inspected the unit and found after running for five seconds unit would power off. Ordering parts. ; ordrng 1 137392702 (Heater) and 1 134120900 (Thermal limit) and 1 5304535307 (Board) and 1 134587700 (Thermistor) and 1 134196602 (Motor) and 1 5304529306 (Board)

Tech was assigned as a helper;

Inspected the unit and found an error code of PC for faulty communication. Order control and display. ; ordrng 1 Xxxx (Control) and 1 Aaaa (Display)

Inspected the refrigerator and found the icemaker dispenser motor stripped not allowing ice to dispense. ; ordrng 1 W11671282 (Dispenser motor) and 1 W11548540 (Ice maker) and 1 WP63052-2 (Yolk)

"Inspected the refrigerator and found the cabling for the deli drawer broken to the UI display causing a E6 error code. Defective deli cable confirmed with multimeter, broken wires. ; ordrng 2 17431000030843 (Deli drawer cable)s"

"Removed unit from wall and checked voltages and found the power supply for communication on main board is not within operating range. From connection on main board X1 to power supply pin 1-2 9.47vdc (normal 9.6vdc) pin 2-3 2.7vdc (normal 4.5vdc) pin 4-5 9.47vdc (normal 9.6) found a faulty reading on pin 2-3 resulting in a communication failure on unit. All other test points tested good. Diagnosis-faulty power supply unit, out of range. ; ordrng 1 00663802 (Power supply unit)"

Inspected the unit and found a failed gasket. Ordering part.; ordrng 1 W10873938 (Gray fresh food door gasket)

Inspected the unit and found a failed control system along with a failed gear case. Ordering parts. ; ordrng 1 WE10M151 (Door assembly) and 1 WH23X10040 (Drain pump) and 1 WH04X25737 (Control) and 1 WH12X10530 (Pressure switch) and 1 WH45X23154 (Inner basket) and 1 WH45X10149 (Outer tub) and 1 WH43X10056 (Agitator) and 1 WH44X27617 (Cover) and 1 WH49X22795 (Gearcase) and 1 WH49X25738 (Motor) and 1 WH01X20436 (Belt) and 1 WH12X10512 (Thermostat assembly)

Installed part. All checks OK

Checked out the unit and found an F4E4 error code. Remove the back panel off the unit and found the relay board was blown. Ordering parts.; ordrng 1 WPW10739349 (Control board) and 1 W10706040 (Wiring harness)

Inspected unit and found the unit not cooling properly in the refrigerator section. Found the evaporator cover with ice build up in the air flow holes and the fan not running. Compressor ran and didnt have any issues. Freezer cooling properly. Discussed with customer potential issues but explained that I need to be able to remove the back evaporator cover to test certain components. Customer to defrost fridge and be rescheduled.

Inspected unit and found unit throwing F 20 code again. Inlet water pressure good. Pressure switch not properly reading water fill. Ordering part.; ordrng 1 W10514214 (Pressure switch)

Replaced harness for burners checked ok

Fixed fill tube for icemaker that was causing unit to leak. Check OK

Installed parts listed, all checked good

Replaced door seal checks ok ; used 1 W11177741 (GASKET) from stock

Replaced control board due to waterline freezing up. Instructed customer to defrost the unit.

Checked unit over found that the unit had blown fuse. Unit ran less then 10 seconds sparked and blew. Wave guide is damaged and this unit is not repairable due to parts being not replaceable.

Replaced shorted heating element. Checks OK; used 1 279838 (ELEMENT) from stock

SR#7741473156. Checked unit over found that unit had a shorted control board and was not heating up properly. This unit has no model and serial anywhere. Customer also could not locate information on unit. I reached out to third-party and provided information. All pictures are attached.

Unit has cracked and broken door hinge. Part is NLA. Spoke with warranty company gave them info.

Checked unit over and found that unit was not draining and would not spin removed front panel and found that there was all sorts of stuffing inside and around the washer. Also found several socks and debris. Drain pump and drain line were completely plugged up. Cleared out drain pump and drain line. Also had to clear out stuffing wrapped around belts and pulleys. Cleared unit out tested checks OK

Installed new wiring harness put unit back together had a couple issues but figured out that there was an issue with the rubber pads behind the user interface so I reverse those got it to work. Everything is working as it should at this point.

Installed defrost timer in refrigerator is now operational. Please allow 6 to 8 hours for fridge to get up to full temperature before putting in any food

"Inspected dryer, found that the heating element had broken on one of the coils, not allowing it to heat. Replaced heating element tested dryer. Dryer is not heating appropriately. ; used 1 WP3387747 ( TS) (Heating element) from stock"

Installed parts listed, all checked good

"Inspected the dishwasher. Customer was saying that it was not working. It was not going through the cycles. I did start a short cycle. Unit was kicking on was introducing water. Arms were moving around. Drain pump was working, but it was working sporadically. Upon further inspection, I pulled out the filter and inside of the drain pump chamber with the filter goes. There was a lot of debris toothpicks toothpick plastic covers, and also some pieces of steel wool that had somehow made it in there as well as some glass and was blocking the water from going out into the drain line. I removed these items tested the drain pump all the water drained out as it should. I also showed the customer the items that I found and I also showed her that the unit is going through the different cycles. You just have to turn the unit on and push the button which is like an arrow to get it to this particular cycle that you want to use. I also did inform the customer that it is important to turn the hot water faucet on at the sink and let the water get hot before starting the dishwasher because she was saying that the dishes were not getting clean, hot water, activates dawn, dish soap, and other soaps to get a proper clean. I also explained the importance of using rinse aid to help in the rinsing in the drying cycles and its also helps with performance in the cleaning cycle as well. I also explained to her the importance of cleaning out the filter itself, making sure that there is no debris in there and that you use a toothbrush or some kind of brush to scrub off the micromesh so that way there is no blockage in your draining. Dishwasher is operating correctly, but if these steps that I had mentioned or not followed, it will affect your cleaning ability for the dishwasher."

Installed part. All checks ok.

Installed parts listed, all checked good

Installed parts listed, all checked good

Installed parts. All checks ok.

"Inspected the unit and found the control board shorted out. Provided info and estimate, declined."

Installed parts, all checked good

Repaired refrigerant leak and recharged unit

Installed parts and recharged system and told customer to give it 24-48 hrs to stabilize

Installed new fill tube and reset ice maker and checks ok

Installed new ice room fan and reset unit and checks ok

Unit still not defrosting called tech line spoke to Robert file#1002938867 he said to replace the defrost timer again gave case # to the customer ; used 1 5304526183 (Timer) from stock

Inspected the unit and found a large amount of ice in the freezer section not allowing the units cool properly. Customer will need to put the unit through a 24 hour defrost to ensure all ice everywhere has been cleared from all passages.

Inspected the unit and found a failed heating element. Replaced element with truck stock. Ran a test cycle. All checks ok; used 1 DE486A (ELEMENT) from stock

Installed parts. All checks ok

Inspected the unit and found 1000 error codes for a stuck UI indicating a failed control system. I did find that the unit needed two firmware updates. Went ahead and updated firmware. Could not get unit to manifest the issue. All checks OK

"Inspected the unit and found a pinch in the drain line, causing a clog. Customer will need to have a certified plumber replace the drain line in order to all reveal the issue of a slow drain."

"Inspected the unit and found multiple cracks in the liner, causing warm air into the system not allowing the unit to cool properly. Screws were rusted into the evaporator cover preventing me from removing it. Called warranty company."

Installed parts, all checked good

Installed parts listed, all checked good

"Checked out the unit and found that the door latch was stuck, closed and would not allow the door to close properly. Removed the door panel and adjusted the door latch. Checks OK"

Checked out the unit and put it into diagnostics and put it into a spin cycle and the unit was spinning and balancing correctly. Made adjustments to the suspension rods to make sure it was bouncing properly. Ran another test cycle and the unit was balancing correctly. Advise the customer to make sure when they're running loads to make sure that when washing baby clothes they arent washing any large items with it due to it having a hard time balancing. Checks OK

Checked out the unit and found that the icemaker had ice in it but the cubes on one side of the icemaker were very small. Installed a new icemaker and advise the customer to give it 24 to 48 hours before it starts making consistent ice. Checks OK; used 1 243297608 (ICEMAKER) from stock

"Check out the unit and found that the back of the filter head line was partially kinked and some ice buildup, not allowing the water flow. Made adjustments to the line and also replaced the filter due to the old one being bad. Called and informed warranty. Checks OK"

"Checked out the unit and found the unit heating properly, but not drying the clothes in one cycle. Ran a test cycle and found poor airflow getting outside due to blockage in the line. Advise customer to talk with property management regarding the blockage in the vent line. Checks OK"

"Checked out the unit and found that the unit was in defrost mode, and I was unable to advance it out of the defrost mode. Replaced the defrost timer and advise customer to give it 24 to 48 hours for the temperatures to get back to cooling. Check OK; used 1 5304526183 (DEFROST TIMER) from stock"

"Checked out the unit and found the unit not heating, but when starting a test cycle after about 5 to 10 seconds heard several shorting out noises coming from the magnetron. You could see from the inside of the cabinet that it was shorting out on the back of the cabinet of the microwave. Unit will need to be replaced. Unit is approximately 10 years old and located in the kitchen. Called and informed the warranty company."

Checked out the unit and found a large amount of ice and frost buildup around the fan not allowing the fan to blow the cold air up throughout the unit. The temperatures in the freezer were sitting around 30?. Remove the evaporator cover and found more ice buildup down around the evaporator. Steamed out a lot of the ice around the fan. Advise the customer tocompletely defrost the unit for 48 hours due to the amount of frost and ice buildup. After the 24 hours the customer to plug it back up and keep an eye on the temperatures. Checks OK

Installed parts listed, all checked good

Installed new parts. All checks ok.

"Inspected unit and found the unit not spinning properly. Unit would not drain due to motor not wanting to run at all. Put unit into diagnostic mode and found f5a code for the motor control thinking the motor is overheated. Unit was not overheating at all. Basket would spin without resistance, as would motor. Motor windings checked good and within spec. Per Electrolux, this means the motor control would need replaced. Gave customer quote for motor control replacement. Customer to think about repair."

Inspected unit and found unit was still throwing le code. Unit would spin properly but not agitate right. Made adjustments to shifter and slider. All checks ok.

Installed new parts. All checks ok.

Installed parts listed, all checked good

Installed parts listed, all checked good

Door bellow is cut in 2 different places ordering door bellow.; ordrng 1 W1106747 (Bellow)

Installed parts listed, all checked good

Installed parts listed, all checked good

Found the front right burner activating when turning on another burner. Ordering parts. ; ordrng 1 Xxxx (All four infinite switches) and 1 Zzzz (Main wiring harness for display and infinite switches)

Motor no longer running. Ordering part. Advised the customer they would need to have the unit removed from under the cabinet before we can complete repair due to condition of counters and floor. ; ordrng 1 W11416362 (Motor assembly)

"Inspected the unit and found the wash motor with low water flow, the door gasket faulty, the control board failing while entering diagnostics, the tub covered in some form of corrosion due to the heating element failing, the heating element cracked, damage to the front door. The unit is almost 12 years old and located in the kitchen. Not a recommended repair as parts are not available and not repairable. ; ordrng 1 W10518394 (Element) and 1 W10440715 (Motor (nla)) and 1 W10482482 (Sump) and 1 W11513967 (Inner door) and 1 W10350251 (Panel (nla)) and 1 W10195329 (Seal (nla)) and 1 8171656 (Outer door panel (nla)) and 1 W10482988 (Control) and 1 Zzzz (Tub (not a replaceable part))"

Compressor shorted, installed new ; ordrng 1 5304537795 (Compressor) and 1 5304526183 (Timer)

Inspected the unit and found a failed defrost timer. Ordering part ; ordrng 1 5304526183 (Defrost timer)

Inspected the unit and found a failed igniter. Replaced with truck stock. Ran a test cycle. All checks OK; ordrng 1 5304534663note (Igniter)

Installed parts listed

Unit needs new drain pump. No repair