If you have a problem with your Samsung dryer, newer models display an error code to let you know the nature of the issue. This handy guide outlines the meanings of the main Samsung dryer error codes and gives you advice about how to solve them. Thankfully, most of the error codes are simple to resolve and do not require a technician.
This guide covers all major models of Samsung Dryers, including:
DV203AEWXAA
DV203AGSXAA
DV203AGWXAA
DV206AESXAA
DV206AGSXAA
DV209AEWXAA
DV210AEW/XAA
DV210AEWXAA
DV210AGWXAA
DV218AEBXAA
DV220AEW/XAA
DV330AEW/XAA
DV350AEWXAA
DV419AEWXAA
DV42H5000EW/A3-0000
DV42H5200EP/A3-0000
DV42H5200EW/A3-0000
DV448AEP/XAA
DV448AEPXAA
DV45H7000EW/A2-0000
DV48H7400EW/A2-0000
Please note: If your Samsung dryer does not have a digital display, it displays error codes as flashing lights instead. You can find out which error codes the flashing corresponds to by consulting your user manual.
This error code comes when a problem with the dryer’s voltage supply arises. To solve this issue:
These error codes concern the door, the latch, and the sensors that determine if the door is properly closed. This may occur if the door does not latch, close, or stay closed.
Verify that the door is closed and locked properly, that no laundry or other items are stuck between the door and the opening, and that the latch is firmly fixed.
If the code cannot be fixed or if you see obvious damage to the door or latch, you may need to replace the latch mechanism.
This displays if a panel button is stuck or is being pressed continuously.
If you encounter this error, turn off the dryer’s power before manually pressing and releasing each button on the control panel while moving your finger back and forth to touch each button’s edges.
You might need to replace the control panel if any buttons are broken or if the dryer’s error code reappears after turning on the dryer again.
These show a problem with the sensors used to monitor the temperature.
The most frequent reason is a heat-trapping vent system or clogged lint screen in the dryer. To fix the problem, clean the vent system, lint screen, or both.
If this does not clear the error code, you may have to look into replacing the temperature sensor.
This indicates that the dryer is becoming overheated.
The most frequent reason is a heat-trapping vent system or clogged lint screen in the dryer. To fix the problem, clean the vent system, lint screen, or both.
Low voltage can sometimes be the root of the problem, which manifests as the heater not getting hot enough. You can check the voltage of your dryer with a multimeter to determine if this is the cause of the problem.
This error code means that the internal parts of the dryer cannot communicate with one another. To clear this code, the dryer should be turned off for 60 seconds before being turned back on.
In most cases, this should clear the error code, but if it does not you need to hire a professional to investigate further.
These codes indicate that the power source frequency is incorrect. Try restarting the cycle to resolve this. As with the codes that indicate communication errors, if this code is not easily cleared, it requires a professional to investigate further.
These codes appear only after a Vent Blockage test has been performed. You may choose to perform this test if you suspect that your vent is obstructed. The following is a list of the meanings of each individual code:
Clg, Cg – The vent has become obstructed.
C80, C8 – Approximately 80% of the vent is blocked.
C90, C9 – Approximately 90% of the vent is obstructed.
C1, CL1 – Laundry has been detected within the drum.
Ct – The dryer is either below freezing or above 104°F.
If the dryer displays an error code that is not on the list, the problem is usually with the dryer’s sensors and components.
Here are a few examples:
1 AC7 – Electronic Control Error
3C – Motor Error
1 AC7 – Electronic Control Error 3C – Motor Error
HC2 – Gas Ignition Failure
If you receive one of these or any other errors, turn off the dryer for 2–3 minutes, then turn it back on and restart the cycle. If this does not work, consult your user manual for specific troubleshooting steps.
There are several possible reasons why the ice maker in a Whirlpool refrigerator might stop…
It can be frustrating when your LG refrigerator stops making ice as it should. There…
Kenmore refrigerators are renowned for their reliability and durability, but some users do occasionally encounter…
Dealing with unpleasant odors in your refrigerator is always stressful, and fish smells might be…
It’s always stressful when you have an issue with your dishwasher—after all, no one likes…
If your Whirlpool dishwasher isn’t draining, your first instinct might be to contact an appliance…
Leave a Comment