Replacing the freezer door seal can be easy once you know what to do. It doesn’t take much time, and it will be a lot cheaper if you can do it yourself. Here’s a quick guide on how to remove the freezer seal and install a replacement.
Over time, the freezer seal, also called the gasket, will wear out. Wear and tear commonly occurs on the hinge side of the door, and because of this, you are less likely to notice it.
However, you may have already noticed that the freezer door is not closing properly. If that’s the case, it’s time to replace the seal.
Replacing the seal is essential. If you have been putting it off for some time, then now is the time to replace it.
Replacing the freezer’s seal will:
To replace your freezer’s seal, you will need to find the model number of your freezer. Some model numbers are located on the inside of the freezer, while others are located on the outside.
Once you have found the model number, you can search for an online store that sells freezer gaskets for your model. Depending on how old your freezer is, you might be able to buy a new seal from the manufacturer.
If you cannot find an exact match, that’s okay because there are universal freezer seals available instead. However, if you opt for a universal seal, you still need to find one suited for your freezer.
When looking for a universal seal, you will need to measure the existing seal in millimeters.
Measurements you may need include:
Some universal seals are ready-made, and you won’t need to worry about the length. However, if you cannot find a ready-made one for your freezer, you will need to measure the length because you will need to cut the seal to fit your freezer.
You also need to consider the type of seal your freezer has.
There are three main types:
What you will need:
Before starting any work on a freezer, always unplug it first.
Before removing the old seal, ensure the new one will fit. To do this, hold the new seal against the old one to ensure it’s the same size.
If you are installing a universal seal make sure that the new seal you have is the same type as the current one. Additionally, if you are measuring the seal and cutting it to length, make sure that you have enough before you start.
If you are installing one that is suited to your model, ensure that you received the right one before installing. Check the packing or compare the new one to the old one.
If the seal is screwed in, you will need to remove the screws first. You may need to fold back the seal to find the screws. Ensure that you keep the screws somewhere safe because it might be hard to replace them should they get lost.
Other than that, all you need to do is run the putty knife under the seal and pry it away from the door. Start from one corner first, and work your way along the seal.
Once the seal is off, use a damp cloth to clean the door where the seal was previously. Cleaning this area will ensure that the new seal sticks properly.
What you will need:
You can still install the new seal with the door on. However, you may find removing the door and laying it on the ground or a table easier.
To remove the door, unscrew it from the hinges.
If you prefer to leave the door on, ensure that the door is supported to prevent it from moving.
Always start from the corners first, regardless of which seal you are installing. Once the seal is installed in all four corners, secure it around the edges. Do not secure it around the edges first because this may stretch the seal.
However, if you are using a universal seal that is being cut to length, you will need to start at one corner and then work your way around. Avoid cutting the seal to size until you have almost finished installing it.
If you have difficulty securing the seal into the groves of the door, use the flathead screwdriver to pry the grooves back slightly. The flathead screwdriver might also be useful for pushing the seal into the grooves.
Don’t forget to install the screws, if the seal is a screw-in one.
In most cases, you do not need to glue the new seal because it should fit into place securely with the grooves.
However, if you use a universal seal, you may wish to use glue because it may not be an exact fit.
You can also use glue if the seal refuses to stick in one place. Simply apply some glue under the seal in that area and hold it in place until the glue has dried.
If you decide to use glue, you will need to buy one that is suitable, such as flex glue or cyanoacrylate superglue.
After you have installed the new seal, you will want to prevent it from wearing out like the previous one. While most wear and tear is unavoidable, there are some things you can try to prolong the life of the new seal.
Prolong the seal’s life by:
There are several possible reasons why the ice maker in a Whirlpool refrigerator might stop…
It can be frustrating when your LG refrigerator stops making ice as it should. There…
Kenmore refrigerators are renowned for their reliability and durability, but some users do occasionally encounter…
Dealing with unpleasant odors in your refrigerator is always stressful, and fish smells might be…
It’s always stressful when you have an issue with your dishwasher—after all, no one likes…
If your Whirlpool dishwasher isn’t draining, your first instinct might be to contact an appliance…
Leave a Comment