Your refrigerator’s water inlet valve is what sends water from the home’s plumbing into your ice maker for cold water and fresh cubed ice. If the inlet valve has stopped supplying water or it won’t stop flowing, then it’s time for a replacement. Let’s dive straight into the process of how to replace your refrigerator water inlet valve.
It’s always best to start with all of your supplies before a repair. The most important part is the replacement inlet valve. Be sure to match the replacement part to the make and model of your refrigerator.
Start by removing all the perishables from your refrigerator and storing them in a nearby cooler. The fridge will be off for the duration of this repair and will need to be moved, shaking the shelves. So it’s better if the fridge and freezer foods were stored safely until the repair is done.
Carefully pull your refrigerator out of its nook and away from the wall. You will need room to work behind the refrigerator where the inlet valve is located. Carefully rock your refrigerator, holding both sides, to pull it out.
Unplug your refrigerator. If the plug is difficult to reach, you can also flip the breaker that supplies power to your fridge.
Close the water supply cutoff valve behind your refrigerator. Then identify the water valve assembly in the back of the fridge. It should be near the bottom and is often blue with a water line running into it. Place a towel under the valve. Then loosen the compression nut and pull the water line free.
Looking at the back of your fridge, you should see a lower panel cover attached with two to six screws. Remove the screws from the lower panel. Then carefully lift and remove the back lower panel.
Set both the panel and the screws aside somewhere nearby, as you will need them later. Make sure to put the screws in a small container to they don’t roll away.
Find the water inlet valve. It is often blue and fastened to the outer edge of the refrigerator frame, just behind the panel. The inlet valve is connected by a plastic water line to your ice maker and is the part you already disconnected the refrigerator water line from when the back panel was still attached. This should make it easier to find.
Remove the two screws holding the valve mounting bracket to the refrigerator’s frame. Set these screws aside as well and pull the inlet valve free. It is not connected by a bundle of wires and the water line to the ice maker.
There is a cluster of plastic-wrapped wires connected with a plastic clip. This is the wire harness. Disconnect the wire harness clip so that the valve is free of the wire connection.
The water line running into the valve can be removed by pressing in and then pulling out. This is the line to the ice maker. Now your inlet valve should be completely free. You can now throw it away or save it for recycling.
Take your new water inlet valve and thread the ice maker water line into the correct aperture. Press it in to secure the pressure fastener type.
The new inlet valve will have a mounting point for the wire harness. Connect the refrigerator’s wire clip to the new inlet valve and click it into place.
Hold the inlet valve in place against the refrigerator frame, lining up the bracket with the available holes. Then use the screws you set aside to reattach the new inlet valve to the refrigerator frame. Tighten the screws securely.
It’s time to put the back panel into place. Check the ice maker line to the inlet valve one more time to make sure it’s secure and water-tight. Then heft the back panel back over the aperture of your refrigerator. Hold the panel and return the mounting screws to secure the back panel into place.
It is now safe to turn the water back on for your fridge. Start by reattaching the water line to the new inlet valve through the opening in the back panel. From there, switch the shutoff valve open. Then turn on the water at the wall, if you have a wall valve as well near your fridge.
When you’re sure there isn’t an immediate leak, return power to your refrigerator. If you switched off a breaker, switch it back on. If you unplugged the fridge, plug it back in. The repair is over and it’s time to test your success.
All your behind-the-fridge work is done. You can now carefully push your fridge back into its nook with the fridge back against the wall. Work slowly and ask a friend for help, if necessary. Don’t hurt yourself or tilt the fridge too much while moving it.
With your fridge back on the job of generating cold, it’s safe to fill it back up with all the cold goods in your kitchen. Empty the coolers you filled earlier back into the fridge and freezer. Be sure not to block the vents and take this opportunity to reorganize how you store foods, if you care to.
Finally, test whether your repair was a complete success. Run a few cups of cold water through the fridge dispensing system to see if it comes out clean without interruption or leaking. Then give your fridge time to make some new ice. If all comes out well, then you have successfully repaired the inlet valve of your fridge.
There are several possible reasons why the ice maker in a Whirlpool refrigerator might stop…
It can be frustrating when your LG refrigerator stops making ice as it should. There…
Kenmore refrigerators are renowned for their reliability and durability, but some users do occasionally encounter…
Dealing with unpleasant odors in your refrigerator is always stressful, and fish smells might be…
It’s always stressful when you have an issue with your dishwasher—after all, no one likes…
If your Whirlpool dishwasher isn’t draining, your first instinct might be to contact an appliance…
Leave a Comment